Key Features
Locks Pieces Flush The Kreg Tool KHC-PREMIUM locking face clamp is built to hold two workpieces even while you drive screws, which helps keep faces lined up instead of shifting at the last second. Made for Joinery This face clamp is shown doing exactly what most buyers need it for: holding pocket-hole and face-frame parts in position so assembly goes faster and cleanup stays minimal. Simple Manual Setup No batteries, no hose, no extra setup. Just adjust the screw, lock the clamp, and get steady pressure where you need it.
Overview
Kreg Tool KHC-PREMIUM locking face clamp is a manual woodworking clamp built for holding parts flush during assembly. This is a face clamp designed for pocket-hole joinery, face-frame assembly, and general woodworking alignment. Model Number: KHC-PREMIUM. If you build cabinets, frames, boxes, or furniture parts and need boards to stay lined up while you fasten them, this is the kind of clamp that earns its spot on the bench fast.
The big advantage here is control. Instead of trying to hold two pieces by hand while driving a screw, the clamp applies pressure across the joint so the surfaces stay even. In the product images, the clamp is used across pocket-hole workpieces and face-frame parts, which is exactly where this style helps most. It reduces creeping, keeps edges flush, and makes it easier to get cleaner-looking results the first time.
Design-wise, this is a locking plier style clamp with an adjustment screw at the end of the handle and broad round clamping pads at the jaw. That matters because you get repeatable pressure once it is dialed in, and the pads spread force over a wider contact area than a narrow tip would. For assembly work, that usually means less marring and better holding on flat stock.
The overall shape also makes sense for the job. The deep frame reaches over adjacent parts while the round pad bears down near the joint line. On pocket-hole assemblies, that lets you clamp right where movement wants to happen. On face frames, it helps pull rails and stiles into alignment so you are not sanding away a mismatch later.
Because the Kreg Tool KHC-PREMIUM locking face clamp is manual, it is easy to move from joint to joint without dragging cords, hoses, or chargers around the workspace. That makes it just as useful on a dedicated bench as it is for quick assembly work in a garage shop or on a jobsite. The rubberized grips shown in the images also make it easier to open and close repeatedly during production-style work.
This clamp is best suited for woodworkers, cabinet installers, trim carpenters, and serious DIYers who do a lot of screw-based assembly and want tighter, cleaner joints with less fighting. If your work regularly involves pocket-hole screws, face frames, or keeping boards flush during fastening, this tool solves a real problem in a very direct way.
Hold Joints in Place While You Fasten
Most assembly mistakes happen when the parts shift right as the screw goes in. This clamp is built to stop that by holding the joint steady and the faces even.
- Shown clamping face-frame style stock during pocket-hole assembly
- Round jaw pad applies pressure near the joint where alignment matters most
Get Better Alignment on Flat Stock
When you are joining boards that need to stay level with each other, clamp placement matters. The jaw shape and pad layout are aimed at flat, face-to-face clamping instead of just squeezing from the edge.
- Useful for keeping adjoining workpieces flush during screw assembly
- Locking mechanism helps maintain pressure without constant hand force
Quick to Set, Easy to Repeat
Once the adjustment screw is dialed in for your material thickness, you can move through repeated joints faster. That is a big help when you are building multiple frames or cabinet parts.
- Adjustment screw at the handle end lets you tune clamping pressure
- Manual operation means no batteries, hoses, or power source required
Key Specifications
| Tool Type | Locking face clamp |
|---|---|
| Power Source | Manual |
| Clamp Style | Locking plier style |
| Jaw Pad Type | Round swiveling pads |
| Handle | Rubberized grips |
| Primary Use | Holding workpieces flush during pocket-hole and face-frame assembly |
Built For
Woodworking Cabinet Assembly Face Frames Pocket-Hole Joinery Furniture Building Carpentry
Pro Tip
Set the clamp pressure using scrap that matches your project thickness first. Once it is dialed in, you can move from joint to joint faster and keep the faces flush without over-squeezing the work.
Tool Nut’s Take
Tool Nut’s Take
Kreg Tool KHC-PREMIUM locking face clamp for faster, cleaner assembly
This is the kind of simple shop tool that saves more time than people expect once they start doing repeat assembly work.
- Who it’s for: Woodworkers, cabinet guys, trim carpenters, and DIYers building face frames, boxes, and pocket-hole projects.
- Why it stands out: It is purpose-built to keep parts flush while you drive screws, which is exactly what makes pocket-hole assembly go smoothly.
- Worth knowing: This is a manual clamp, not a general replacement for every bar clamp in the shop. It shines most when alignment at the joint matters more than wide clamping reach.
Common Questions
- What type of tool is this? It is a manual locking face clamp used to hold workpieces flush during assembly.
- What kind of work is it shown doing? The images show it being used for pocket-hole joinery and face-frame style woodworking assembly.
- Does it need batteries or power? No. This is a manual clamp with a locking plier style mechanism.
Reviews
There are no reviews yet.