Key Features
Angle holes without tilting Woodpeckers DUAX-DEL Duax Angle Drilling Table – Deluxe Kit lets you drill accurate angles from 0 degrees to 90 degrees without messing with your drill press table setup. Locks in the angle Laser-cut teeth and stainless steel side quadrants hold your setting under drilling pressure, so your angles stay consistent from part to part. Deluxe clamping control The included clamping kit helps keep stock from walking: wedge clamping system, hold-down clamps, and button stops for repeatable positioning.
Overview
The Woodpeckers DUAX-DEL Duax Angle Drilling Table – Deluxe Kit (Model DUAX-DEL) is a drill press accessory designed for drilling accurate angled holes and compound-angle joinery without changing the angle of your drill press table. It is built for woodworkers who want repeatable results on parts that meet at an angle, like stool and chair components, racks, holders, and any project that uses dowels or round tenons.
The system is a two-piece setup: a base and an adjustable angle table. The adjustable angle table mounts to the base in four orientations so you can aim the angle where you need it and still keep clearance for the drill press column, clamps, and your workpiece. The table and fence do the positioning work; you set the angle, line up the part, and drill.
Angle holding is where this setup earns its keep. Laser-cut teeth engage for accurate angle settings, and stainless steel quadrants on both sides of the table secure the angle even when you lean into the feed handle. That matters when you are drilling larger holes, using Forstner bits, or drilling across end grain where the tool pressure wants to shift the work.
The “dual” in dual-axis comes from the adjustable fence. It can be set for any angle between 0 degrees and 90 degrees in either direction and positioned anywhere along the table, which helps when you need the work referenced off a fence but still want freedom to place the drilling point exactly where the layout calls for.
The Deluxe Kit adds clamping that is actually useful for angled drilling. The wedge system clamps your work against the fence, and the wedge gets tighter as drilling pressure increases. You also get hold-down clamps to keep the stock planted to the table, plus button stops you can locate in the table slots for repeatable placement, especially with round objects.
Jobsite practicality is baked in. There is a vee-groove down the center of the table to cradle round stock for drilling across the diameter, and the Duax can be adjusted vertically so you can hang it off the edge and drill the ends of longer parts. It is optimized to mount on the Woodpeckers DP-PRO Drill Press Table and earlier Woodpeckers drill press tables, but the attachment slots are designed to work with many drill press table hole and slot patterns. It is intended for drill presses with 12 inch capacity and larger.
Made in Strongsville, Ohio, this is the kind of drill press jig you buy when you are tired of “close enough” angles and you want a repeatable process: set it once, clamp it, and drill a batch of parts that actually match.
Hold Round Stock Steady
Round parts are where angle drilling gets sketchy fast. The center vee-groove gives you a stable cradle so the bit starts where you want, not where the stock decides to roll.
- Center vee-groove supports round stock for drilling across the diameter
- Designed to keep work aligned while you drill at an angle
Repeatable Positioning
If you are drilling more than one part, stops matter. Button stops let you put round stock in the same spot every time, so the layout stays consistent across a set.
- Includes (2) button stops for locating round work in the table slots
- Helps keep hole spacing consistent when drilling multiple parts
Clamp Fast, Clamp Tight
Angled drilling tries to pull the workpiece out of position. The wedge clamping system locks the stock against the fence, and drilling pressure only makes it bite harder.
- Includes wedge clamp system for fence-referenced clamping
- Includes (2) hold-down clamps to keep work planted to the table
Set the Angle, Keep the Setup
Instead of tilting your drill press table and fighting to get it back to square, you set the work on the Duax, lock it down, and drill. Your main drill press stays dialed in.
- Adjustable angle range: 0 degrees to 90 degrees
- Table can mount to the base in four directions for clearance and angle orientation
What’s in the Box
- Duax base
- Adjustable angle table
- Adjustable fence
- (2) hold-down clamps
- Wedge clamp system
- (2) button stops
Key Specifications
| Tool Type | Drill press angle drilling table and clamping jig (drill accessory) |
|---|---|
| Angle Range | 0 degrees to 90 degrees (dual-axis fence adjustment in either direction) |
| Weight | 13.0 lb |
| Minimum Drill Press Size | 12 in capacity and larger |
| Made In | USA (Strongsville, Ohio) |
| Patent | U.S. Patent No. 12,491,568 |
Compatibility
Drill Press Tables Optimized for the Woodpeckers DP-PRO Drill Press Table and earlier Woodpeckers drill press tables; attachment slots also fit many drill press table hole and slot patterns. Drill Press Size Intended for drill presses with 12 inch capacity and larger.
Built For
Woodworking Chair and stool joinery Dowel and round tenon joints Compound-angle drilling Round stock drilling Repeatable batch drilling
Pro Tip
When you need to drill into the end of a long part (like a stool leg), set the Duax up vertically and hang it off the edge of the drill press table so the stock can clear the table instead of fighting you.
Tool Nut’s Take
Tool Nut’s Take
Why the Woodpeckers DUAX-DEL Duax Angle Drilling Table – Deluxe Kit is worth the bench space
This is the cleanest way to do accurate angle drilling on a drill press without giving up your dialed-in 90 degree table setup.
- Who it’s for: Woodworkers building chairs, stools, racks, and anything with dowels or round tenons that needs repeatable angles.
- Why it stands out: Dual-axis positioning with a fence, plus angle locking hardware designed to hold steady under real drilling pressure.
- Worth knowing: It is intended for drill presses 12 inch capacity and larger, and mounting depends on your table slot and hole pattern.
Common Questions
- What angles can it drill? The adjustable fence and table system is designed to work from 0 degrees to 90 degrees in either direction.
- Do I have to tilt my drill press table? No. The Duax is designed to set the work at the angle you need while keeping your drill press table at its normal setting.
- What drill presses does it fit? It is intended for drill presses with 12 inch capacity and larger, and the base slots are designed to work with many drill press table hole and slot patterns.
- Where is it made? It is made in the USA in Strongsville, Ohio.
Reviews
There are no reviews yet.