Woodpeckers SS4K-CL Stealthstop 4′ Kit – Combination, Left

Key Features

Micro-Adjustable Stops The flip stops lock firmly, then fine-tune with a thumbwheel so you can dial in repeat cuts without sneaking up on the measurement. Three Mounting Options Mount the track vertically, flush it into the table, or run a stacked setup. That gives you more ways to fit the stop system to the saw station you already have. Built for Shop Use Glass-reinforced polycarbonate, stainless and zinc-plated internals, and a brass thumbwheel give this Woodpeckers stop system low-maintenance durability where cheaper stops get sloppy.

Overview

The Woodpeckers SS4K-CL Stealthstop 4′ Kit – Combination, Left is a micro-adjustable flip stop system for a miter saw station. This is a miter saw stop system designed for repeatable length cuts and fast setup on a cut station. Model Number: SS4K-CL. If you build cabinets, trim parts, face frames, or any run of identical pieces, this system matters because it lets you set a stop once, adjust it precisely, and get back to cutting instead of measuring every board.

What makes the StealthStop different is how the stop works inside the track. It glides in the miter gauge slot of Woodpeckers Combo Track, locks with a simple twist of the included hex key, and folds completely down into the slot when you do not need it. That means the stop stays out of the way without forcing you to remove it or lose your setting. Flip it up and it locks square to the track, giving you a rigid reference point for repeat cuts. The micro-adjust thumbwheel is the part serious woodworkers will appreciate most. Instead of tapping the stop by hand and hoping it stayed put, you can creep up on an exact measurement with control.

The combination kit layout is built around flexibility. According to the product information, StealthStop can be installed three ways: vertical, horizontal flush mount, or stacked with a vertical track on top of a horizontal track. That stacked configuration is the real advantage if you want stops very close to each other. Woodpeckers uses specially designed brackets to link the horizontal and vertical tracks at 90 degrees, which gives you stop positions in both fences. On a miter saw station, that can be a big deal when you are switching between close dimensions or setting up a workflow that needs two reference points within a very small space.

Installation is practical, not fussy. For a vertical mount, the brackets slide into the back of the track and screw to the work surface, creating a setup that feels familiar if you are used to a standard back fence. For a flush-mounted setup, you can route a 1/2 inch deep groove into the table surface. If you do not want to cut into the bench, Woodpeckers also calls out another smart option: mount the track on top of the surface and build the surrounding area flush with 1/2 inch plywood on both sides. That gives you the benefit of a flush work surface without rebuilding the whole station.

Material choices are solid and clearly aimed at long-term accuracy. The main components are injection-molded from glass-reinforced polycarbonate, while the internal parts are stainless or zinc-plated for rust resistance and low maintenance. The micro-adjust thumbwheel is brass, which is a smart call for smooth adjustment and good feel. None of that is flashy, but it is exactly what you want in a stop system that gets handled constantly and lives around sawdust, changing temperatures, and busy shop use.

This left-side version is intended for the left side of the saw, and the product family is offered in left and right configurations based on tape direction and station layout. It is designed to work with Woodpeckers Combo Track, so this is not just a generic stop block. It is part of a track-based measuring and cutoff system. For woodworkers already building or upgrading a dedicated miter saw station, that compatibility matters because it gives you a more integrated setup instead of a homemade stop that works only well enough.

The included 4 foot track format makes sense for most chop saw stations and cutoff benches, and the combination kit adds the expanded track-and-stop arrangement needed for more capable station layouts. If your work is mostly one-off cuts, this may be more system than you need. But if you regularly batch out trim, cabinet parts, shelving components, or repeat furniture pieces, the time savings and consistency are easy to justify.

Bottom line: this is for the woodworker who is tired of measuring, marking, and second-guessing repeat cuts. The Woodpeckers SS4K-CL Stealthstop 4′ Kit – Combination, Left is best for a serious miter saw station where clean setup, precise adjustment, and getting the stop out of the way without removing it all make the work go smoother.

Set Repeat Cuts Without Slowing Down

This is where a good stop system earns its keep. Once the stop is set, you can run repeated miter saw cuts on wood parts without going back to a tape every time.

• Flip stop folds down into the track slot when you need the fence clear
• Micro-adjust thumbwheel helps fine-tune length instead of bumping the stop by hand

Build a Flush Work Surface or a Traditional Fence

Not every cut station is built the same, and that is the point. StealthStop gives you multiple installation paths so you can match the system to your bench instead of rebuilding the bench around the stop.

• Supports vertical mounting, horizontal flush mounting, and stacked track setups
• Flush installation can be done with a 1/2 inch deep groove or by building up both sides with 1/2 inch plywood

Simple Brackets Make Setup More Practical

A stop system is only useful if it actually gets installed. The bracket design keeps the setup straightforward and gives you a clean way to mount the track to the work surface.

• Brackets slide into the back of the track before fastening to the bench
• Bracket design also stores the included 1/8 inch screwdriver-handled hex key

What’s in the Box

• (2) 4 ft. tracks
• (4) stops
• (5) mounting brackets
• (1) combination inch/metric tape
• (1) 1/8 in. screwdriver-handled hex key
• Mounting hardware

Key Specifications

Tool Type	Miter saw stop system
Track Length	4 ft. per track
Configuration	Combination, Left
Mounting Options	Vertical, horizontal flush, stacked
Track Groove Depth for Flush Mount	1/2 in.
Main Material	Glass-reinforced polycarbonate
Internal Components	Stainless or zinc-plated
Weight	7.0 lbs
Made In	USA

Compatibility

Track System Designed to work within the miter gauge slot of Woodpeckers Combo Track. Station Layout This version is the left-side combination kit for miter saw station setups built around a left-hand stop position. Adjustment Tool Uses the included 1/8 inch screwdriver-handled hex key to lock the stops and support installation.

Built For

Woodworking Miter Saw Stations Repeat Crosscuts Cabinet Parts Trim Work Shop Cut Stations

Pro Tip

If you want a flush work surface but do not want to rout the bench, mount the track on top and build up both sides with 1/2 inch plywood. You get the same flush support around the stop track with a lot less commitment.

Tool Nut’s Take

Tool Nut’s Take

Why the Woodpeckers SS4K-CL Stealthstop 4′ Kit – Combination, Left Makes Sense

This is the kind of stop system that pays you back every time you need ten parts to be exactly the same length.

• Who it’s for: Woodworkers building a real miter saw station for repeatable cutoffs, trim parts, cabinet work, and batch work.
• Why it stands out: The stop folds completely into the track, the micro-adjuster gives you real control, and the combination layout gives you more setup flexibility than a basic fence stop.
• Worth knowing: This is a system piece, not a universal clamp-on stop. It is best when you are building around Woodpeckers Combo Track and want a cleaner, more precise station than a homemade setup usually delivers.

Common Questions

• What is this product designed to do? It is a micro-adjustable flip stop system for making repeatable cuts on a miter saw station.
• Can it be installed more than one way? Yes. The product information states it can be mounted vertically, flush horizontally, or in a stacked configuration.
• What track does it work with? It is designed to work within the miter gauge slot of Woodpeckers Combo Track.
• What are the main materials? The main components are glass-reinforced polycarbonate, with stainless or zinc-plated internal parts and a brass micro-adjust thumbwheel.